How to prevent loadshedding in commercial buildings

3 Options to proof your commercial and industrial building from load shedding

The nationwide spate of load shedding in South Africa is not just a highly frustrating situation for individuals: it is a hindrance to businesses and the economy in general. As South Africa starts to approach level 5 and 6 load shedding scenarios, it is important to look at the alternatives available to businesses around the country in order to prevent the loss of productivity across the board. At the same time, various different alternative sources of power should be evaluated based on their cost-effectiveness and environmental impact. The following article explores various load shedding prevention methods for commercial and industrial buildings.

Option 1: Using backup diesel generator

Option 2: Retrofitting a grid-tied solar PV system

Option 3: Going off grid using a solar PV/battery microgrid


Option 1: Using backup generators

This commonly used form of commercial backup power consists of diesel gensets that switch on when the power goes off. This is a good option for ad-hoc power cuts in places that cannot afford to lose power, such as hospitals, convention centres and large retail centres.

Before relying on a diesel backup generator, though, the system should be tested with the total load of the building to make sure that it is able to take the full electricity load. If it not possible for the gensets to handle the building’s entire load, an “emergency” scenario – where nothing but the critical systems are backed up – should be tested. An Automatic Transfer Switch (ATS) will be needed to ensure that when the power goes off, the diesel generators are initiated.

Within Eskom’s current loadshedding trajectory, using backup diesel generators is likely to be very expensive, depending on the load size of the building. Diesel itself is much more expensive per kWh than typical Eskom tariffs, and even more expensive when compared with the costs per kWh of solar PV. When evaluating the efficacy of installing diesel gensets, the following questions should be asked:

  1. How many hours per day will the genset(s) be required?
  2. How many litres of diesel are likely to be required?
  3. What are the ongoing maintenance requirements of consistently using diesel generators?
Robben Island has historically used diesel generators to provide the power needed on the island.
Robben Island has historically used diesel generators to provide the power needed on the island.

Option 2: Retrofitting a grid-tied solar PV system

In South Africa, many commercial buildings – hospitals, retail centres, distribution centres, etc – have grid-tied solar PV systems that supply power from the sun during the day. These relatively simple systems are tied to the grid, so they do not provide 100% of the offtaker energy requirement but rather supplement it. Unfortunately, grid-tied solar PV systems do not automatically prevent a building from experiencing load shedding.

Because solar generates Direct Current (DC) power, this needs to be converted into Alternating Current (AC) to be used in buildings as electricity. In order for a solar system to produce usable electricity, therefore, a solar inverter is required. However solar inverters are designed to switch off during a grid outage.

Why is this? For grid-tied solar PV systems, this serves as a vital safety mechanism for personnel that might be working on transmission lines during outages. With solar inverters off, buildings with solar PV systems are prevented from generating power during a grid outage and potentially exporting power to the national grid, which could be fatal for maintenance personnel.

Solar inverters are designed according to international safety standards that require this functionality, which means that grid-tied inverters cannot operate in off-grid conditions. As such, when Eskom goes down, most solar systems do, too.

However, this does not mean that large buildings with solar PV systems do not have options for load shedding. With careful engineering, It is possible to form one’s own “microgrid”, by replicating a fake grid-tied scenario to “trick” the solar inverters into staying on. This requires the use of a generator or battery, and specialised control equipment.

In order to retrofit a grid-tied solar system to operate during load shedding, two essential steps need to be taken. Firstly, the system needs to be isolated from the grid to prevent any exporting of power that could affect the safety of maintenance personnel. Secondly, a voltage forming source is required, in order to provide a reference voltage and frequency to the solar inverter.

Therefore, to prevent a grid-tied solar PV system from going out during a power outage, the following is required:

  1. Hardware that can disconnect the main supply from the grid, effectively isolating the building/facility from the grid.
  2. A diesel generator or battery bank that can provide backup power for the entire facility and provide the necessary voltage and frequency reference to the solar inverters.

These two points require careful engineering and a proper control system to manage the change-over, the dispatching of generators/batteries, and synchronisation of the solar inverters. It also has to oversee resynchronisation to the grid once the grid is available again. This can be automated and should not need any human input. Further, the system would need to be sized correctly in order not to trip under various loading scenarios.

With these two mechanisms in place, there would be a short down-time after an unexpected grid outage, due to the system having to switch itself on and switch to off-grid mode. Once switched over, however, the solar powered electricity which is being generated can be distributed throughout the building.

In order to avoid an outage entirely, it is possible to either isolate from the grid before an expected outage, or have an uninterruptible power supply (UPS) capable of providing continuous, uninterrupted power during an outage.

solar could help Africa's economy to grow

Option 3: Going off-grid: Using solar PV, batteries and Generators to go off-grid

Taking a commercial building off the grid entirely is another, although slightly pricier, option. Solar PV systems, when combined with energy storage, can store excess solar power produced during the day and distribute this later when needed. Solar PV is now one of the cheapest forms of energy, and its distributed nature means it’s perfect for use at source, where it is needed.

However, the costs of batteries and the sophisticated engineering of microgrid systems needs to be evaluated against the building’s requirements. Perhaps, a commercial or retail building operator does not mind paying a premium if that means consistent, clean power. (Microgrids also have particular relevance to supplying power in weak-grid scenarios – such as the one in Cedar Mill Mall which supplements the grid’s 250 kVA with an additional 250 kVA of power).

If your commercial or industrial building is currently using its diesel generators around 30% of the time, the business case for a solar PV and battery combined microgrid will likely look feasible. In a typical stage 4 load shedding scenario, power cuts generally occur for around 7 hours per day. Given the assumption that the energy load in the building is similar throughout the day and that diesel generators are being used to supply power consistently when the grid goes down, this would equate to around 30% of the total electricity consumption – making it a worthwhile investigation.

Whether it is a backup generator, installing a solar PV system with a backup generator or battery, or going entirely off-grid, there are options for commercial and industrial buildings in South Africa to prevent the damage that load shedding can do to business.

Cedar Mill Mall goes solar
Cedar Mill Mall in Clanwilliam is an islandable on-grid microgrid